Frequently
Asked Questions
How long does it take to set up
the Water Whoosh?
It takes approximately 30 minutes to set up the Water
Whoosh for the first time. This time can be reduced to about 10 minutes
if the slide cover is left on during storage and you gain more experience
setting it up.
-----------------------------------------------------------------------------------------------------
How do you inflate the Water
Whoosh tube?
We highly recommend using an industrial inflator / deflator
like the RAVE Hurricane Blower.
With this blower, it only takes about 5 minutes to inflate the Water
Whoosh tube. You can order this high volume inflator / deflator directly
from Anchor Dock and Lift 320-274-6500. Using the air output side
of a shop vacuum is also an effective way of swiftly inflating the
tube, since shop vacuums typically have high air flow rates.
-----------------------------------------------------------------------------------------------------
Can I use an air compressor
to inflate the product?
We do not recommend the use of an air compressor as
over inflation can damage the tube. RAVE’s commercial grade
products are fully inflated with only 1-2 PSI of air pressure. The
high pressure output of most air compressors can easily cause over
inflation if not monitored properly during the inflation process.
If a compressor is used, be sure not to exceed 2 PSI within the tube.
-----------------------------------------------------------------------------------------------------
How do you deflate the Water
Whoosh?
Again, you can use the RAVE
Sports Hurricane inflator / deflator or a shop vacuum, positioned
in reverse, to swiftly deflate the tube. Another option is to lock
the valve open on the tube and let the air naturally flow out of the
large opening of the valve.
-----------------------------------------------------------------------------------------------------
What is the product made
of?
The inflatable material is the same high-grade material
used in many ocean-going inflatables and inflatable military boats.
It’s a 1000 Denier Polyester with 28 oz. UV treated PVC. All
seams are heat-welded for maximum strength and doubled at key stress
points. We don not use natural rubber or natural rubber latex in any
of our products. Therefore, people with allergic reactions to latex
should not have any problems using our products.
-----------------------------------------------------------------------------------------------------
Can the Water Whoosh be used
in salt water?
Yes, it can be used in the ocean and other salt water
bodies as there are almost no metal components on the product and
they are all made of stainless steel to provide maximum resistance
to corrosion.
-----------------------------------------------------------------------------------------------------
Will the Water Whoosh fade
in the sun?
The tube will retain its brilliance for years because
UV inhibitors are specially blended into the chemistry of our PVC
materials. We also recommend using 303
Aerospace Protectant as a secondary topical agent (like sunscreen
for your skin) to prevent fading and degradation. 303 also restores
lost color and luster, making your product look like new. Periodic
(monthly) application of 303 Protectant will provide the best results.
-----------------------------------------------------------------------------------------------------
Can the Water Whoosh be left
out in the water?
Most people leave their product in the water for the
season. There are two things to consider: 1) your local regulations
regarding anchoring and 2) if the area is consistently exposed to
high winds. In those parts of the world where the water never freezes,
the Whoosh can be left in all year. Specific anchoring recommendations
are provided in the owner manual.
-----------------------------------------------------------------------------------------------------
How deep does the water need
to be to use the Water Whoosh?
We recommend anchoring the product in at least 8 feet
of water in an area at least 20 feet from any docks, boats or other
obstructions. Use reasonable care to ensure that there is adequate
clearance free of obstructions above, around and below the product.
Do not allow the Whoosh to be used on land, in pools or on any other
hard surface.
-----------------------------------------------------------------------------------------------------
How do you anchor the Water
Whoosh?
Sufficient anchoring methods will vary depending on
your local conditions (ex. Water depth, type of water bottom, exposure
to high winds or water current, etc.). Please consult with local authorities
(ie. Dock and lift dealerships, marinas or your local water enforcement
officials) to inquire about proven anchoring methods or anchoring
restrictions in your area. For day use anchoring, a RAVE
Sports sand anchor bag works well. For seasonal anchoring, we
recommend approx. 60lbs of anchor weight. A primary anchor attachment
ring is located on the underside of the slide and a secondary anchoring
ring is located towards the climbing side to help maintain product
orientation relative to the shoreline.
-----------------------------------------------------------------------------------------------------
How can you make your slide
more slippery?
Before sliding down the slide for the first time, treat
the slide surface using 303 Protectant.
This will make the vinyl very slippery even when dry. For better results,
splash some water on the surface of the slide periodically.
-----------------------------------------------------------------------------------------------------
How many people can use the
Water Whoosh at a time?
We recommend only one person climbing and one person
sliding at a time. This will prevent overcrowding and decrease any
chance for collision of users. Supervised activity on the product
is highly recommended. Do not allow anyone to jump or dive off the
top of the slide.
-----------------------------------------------------------------------------------------------------
Does it attach to my Aqua
Jump or other jump platform products?
Although the Water Whoosh was originally designed to
be used in a stand-alone application, it can be butted up next to
most any jump platform product.
-----------------------------------------------------------------------------------------------------
Can the Water Whoosh be repaired
on site?
Yes, Locate the leak or puncture in the product by spraying
the tube with soapy water. When you find the leak and determine the
hole size, use a patch from the repair
kit and cut a swatch 1 inch wider than the hole. Deflate the product
and clean the area around the hole with rubbing alcohol. Apply glue
from the repair kit to the patch and the area around the hole. Let
the glue dry approximately 2 minutes until it becomes tacky. Stick
the glued parts to each other and rub them together using a hard,
smooth, flat surface. Let the patch dry for at least 24 hours before
inflating. For bigger holes and tears, follow the same procedure but
put a patch on the inside as well as the outside.
-----------------------------------------------------------------------------------------------------
What is the warranty on the
Water Whoosh?
RAVE offers a one-year warranty for defects in material
or workmanship. If the product is being used commercially, like at
a camp or resort, there is a 6-month warranty.
<<< back to Water Toys &
Accessories
Expand
your fun by expanding your playground!